Universal Smart TLP-2000 Charger for Li-Ion/Polymer battery Pack (3.7V - 14.8V 1-4 cells) with Lipo Pack Balancer

Features and Benefits

• Smart universal charger for Li-Ion and polymer Li-ion battery pack with capacity > 500mAh
• 4 Voltage selections at 3.6V, 7.2V, 10.8V and 14.4V
• Charges pack made of 1 to 4 cells
• Universal 100V - 240V AC input for worldwide power usage
• 500 mA constant charging current. 
• Automatic charging stop when battery pack is fully charged , or when  each cell 's voltage reaches 4.2V peak
• LED indication: Red means " In Charging "  and Green means " Full " or  "open circuits "
• With Tamiya Conncetor
• Weight: 4.5 oz
• Dimension: 1.5" x 1" x 4"

Operation

• Select right voltage level for your pack.
  • For 3.6/3.7V 1-cell pack, set switch button 4.2 position on the charger
  • For 7.2/7.4V 2-cell pack, set switch button 8.4 position on the charger
  • For 10.8/11.1V 3-cell pack, set switch button 12.6 position on the charger
  • For 14.4/14.8V 4-cell pack, set switch button 16.8 position on the charger

Warning

• Use special caution when working with Li-ion / Li-polymer cells and packs, they are very sensitive to charging characteristics and may explode if mishandled.
• Make sure user has enough knowledge on Li-Ion rechargeable batteries in charging, discharging and assembly before use.
• Put the batteries in fire-proof environment in charging
• Never leave batteries unattended when charging
• Do not put batteries on wood surface or carpet when charging
• We are not responsible for any damage caused by misusing or mishandling of  Li-Ion / Li-Polymer batteries in charging
• We are not responsible for damage caused by other Li-ion batteries not supplied from us
• Do not make any changes to the charger, charger accessories or connectors, as this might cause electrical shortage, fire or over-heating during charging. We are not liable for the product if any changes are made to the charger, accessories or connectors.
  

• Ultra-Balancer is the simplest method of keeping your Lipo packs balanced.
• It can be used for packs up to 14.8 volts (4S).
• Works as a stand-alone balancer before charging or simultaneously with your charger doing it's balancing function at the same time that your pack is being charged.
• 2.5mm spacing on pin connection allows over 90% of the packs in the market to be used without any adapter required.
• offer an adapter in the "Accessories" category to facilitate the balancing of Thunder Power packs.

Connector has 0.100 in pin spacing with 0.025 square pins and fits Apogee and other brands. Pins should be in order: red, black, black and black with no gaps or missing pins in the sequence.

Using Your New Balancer

Low Voltage Check First connect the Balancer to the Li-ion/Li-Polymer pack. Connect the most negative connection on the battery to the most negative pin on the balancer. If all cells are 3.2 volts or more all LED’s will turn on and remain lit for 5 seconds. If you have a three cell pack the first three LED will turn on. If one cell is low and has less than 3.2 volts that LED will not turn on. This means that your battery pack has been discharged too far. DO NOT CHARGE FAST!! Set your charge rate between 0.1 amps and 0.2 amps and wait until the LED’s begin to blink again. This indicates that at least one cell has reached 3.7 volts or more. Disconnect balancer and then reconnect for another Low Voltage Test. Repeat as needed until all LED’s turn on for 5 seconds indicating that all cells have at least 3.2 volts. Then you can proceed to charge normally.

Balancing While Charging Connect the balancer and wait for the low voltage check.

If all cells show 3.2 volts you can proceed with a normal charge sequence. The LED lamps will remain off until one cell reaches a voltage of 3.7 volts. Then balancing will begin. By the time the charge is complete the pack should be balanced. If the cells blink at random the pack is closely balanced. If a few LED’s remain on all the time these cells have a higher voltage then the other cells and more balancing is needed. When the charge is almost complete all the LED’s will turn on.

Balancing After Charging Connect the Balancer to the pack. The balancer will begin discharging every cell that has more than 4.15 volts. When all cells are 4.15 volts or less then the balancer will begin balancing to the lowest cell. When all Led’s turn off or occasionally blink at random, then the pack is balanced